Winston: front hubs and vented brakes

Both front wheel ends, start to finish, written for the parts on the Rovers North order of November 19, 2026. Torque values come from the Discovery I workshop manual (RAVE). Each step shows the socket and the torque.

Vehicle1998 Discovery I LE V8
SpecNAS, LHD, ABS
Job2 hubs, 2 calipers, 2 discs
Tick boxesSaved on this device

Parts check

Lay everything out and count it before the truck goes on stands. Quantities are for both sides.

PartNumberQtyGoes where
Hub assembly with studs (ProLine)PLE2282Replaces each old hub
Hub bearing, cup and cone (Timken)RTC34294Inner and outer, each hub
Hub inner sealFTC47852Back of each hub
Keyed spacing washerFTC52412Against outer bearing
Hub nutFRC87004Adjusting nut and locknut
Lock washerFTC31792Between the two nuts
Drive flange gasket5717522Flange to hub
Drive flange boltBX110095M105 per flange
Driveshaft circlip5494732End of each shaft
Dust capFTC54142Flange center
Disc to hub boltLR082331105 per disc
Vented discLR1890512Bolts to new hub
Caliper, vented type (ProLine)PLF301A left, PLF300A right1 + 1Swivel housing
Caliper bolt M12 x 35SYP50009042 per caliper
Front pads, ventedSFP0002601 setBoth calipers
Mudshield kit, galvanized (YRM)PLB1778G1Behind each disc

Not on the order, needed to finish

ItemNumberWhy
Pad pin kitSTC8575New retaining pins, springs and split pins for vented calipers
Stub axle joint washerFTC3648 x 2RAVE fits the mudshield under the six stub axle bolts, so the joint is disturbed
Swivel housing oilEP90, about 0.35 L per sideThe swivel is drained to take the stub axle bolts out
Brake lineCopper-nickel line and fittings, or new hosesThe vented caliper inlet sits in a different place
Brake fluidDOT 4, 2 liters, sealedFull bleed
GreaseNLGI-2 multipurpose lithiumHub bearings
ThreadlockerLoctite 270Disc bolts, flange bolts, stub axle bolts

Tools and socket sizes

RAVE gives torque, not socket sizes. The sizes below come from owner write-ups for this axle. Test each socket for a snug fit before you put force on it.

FastenerSocket or wrenchTorque
Hub adjusting nut and locknut52 mm deep61 Nm (45 lb-ft) then see step
Caliper bolts13 mm 12-point (a 1/2 in 12-point also fits)82 Nm (60 lb-ft)
Drive flange bolts17 mm65 Nm (48 lb-ft)
Disc to hub bolts14 mm 12-point73 Nm (54 lb-ft)
Stub axle bolts17 mm confirm on truck65 Nm (48 lb-ft)
Brake pipe and hose unions11 mm flare-nut15 Nm (11 lb-ft)
Bleed screws11 mm check on new calipers15 Nm (11 lb-ft)
Road wheel nuts27 mm factory nut, check yours126 Nm (93 lb-ft)

Also needed: axle stands and wheel chocks, torque wrench covering 60 to 130 Nm, a small torque wrench that reads 4 Nm (35 lb-in), brass drift or bearing race driver, seal driver or a flat block, hammer, circlip pliers, flat chisel or punch for the lock washer tabs, dial gauge with magnetic base, brake hose clamp, tube bender and flaring tool if you make lines, bleed bottle and hose, brake cleaner, lint-free rags, drain pan.

1. Strip one side

Do one side at a time so the other stays assembled as a reference. Start with the left, the side that overheated. RAVE 60.25.01 and 70.55.03.

Inboard (axle side)Outboard (wheel side) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Fig. 1. Front hub, exploded in assembly orderSchematic, not to scale
No.PartNew or reused
1Inner sealNew, FTC4785
2, 5Inner and outer bearingNew, RTC3429
3Vented discNew, LR189051
4HubNew, PLE228
6Keyed spacing washerNew, FTC5241
7, 9Adjusting nut and locknutNew, FRC8700
8Lock washerNew, FTC3179
10Drive flange gasketNew, 571752
11Drive flange (drive member)Reused if splines are good
12Flange bolts, 5New, BX110095M
13Driveshaft shimReused. Keep left and right apart
14CirclipNew, 549473
15Dust capNew, FTC5414

2. Inspect before anything goes back

This is the only chance to see what actually failed. Photograph each item.

Stop if the stub axle bearing surfaces are blue, straw-colored, scored, or have a ridge you can catch with a fingernail. That stub axle must be replaced (FTC3154) before a new hub goes on it.

3. Mudshields

RAVE mounts the mud shield under the six stub axle bolts, so fitting the new YRM shields means disturbing the stub axle joint. If the joint washers and swivel oil are not on hand yet, skip this section and fit the shields later. RAVE 60.15.43.

Flat at 12 o'clock Six bolts, Loctite 270, tighten evenly 65 Nm (48 lb-ft) Mud shield sits under the bolt heads New joint washer behind the flange
Fig. 2. Stub axle flange, viewed from the wheel sideSchematic, not to scale

Not in RAVE The shield is listed for the vented Defender front, but this truck is a conversion. Clearance is checked in section 6.

4. Build the new hub on the bench

RAVE 60.26.14 and 70.10.10. Work clean. Grit in a new bearing is what this job is fixing.

Not in RAVE If you are painting the bare hub and caliper castings, do it first and let the paint cure fully. Mask the bearing bores, the seal seat, every mating face, all threads and the wheel face.

1 2 3 4 5 Tighten across, never around Disc to hub: 73 Nm (54 lb-ft), Loctite 270 Drive flange to hub: 65 Nm (48 lb-ft), Loctite 270 Wheel nuts: 126 Nm (93 lb-ft) Snug all five by hand first, then torque in this order in two passes.
Fig. 3. Five-bolt tightening orderSchematic, not to scale

5. Fit the hub and set the bearings

RAVE 60.25.01. The nut sequence in steps 3 to 5 sets the bearing preload. It is the most important measurement in the job.

A. 61 Nm (45 lb-ft)Turn the hub while tightening B. Back off 90 degreesOne quarter turn loose C. 4 Nm (35 lb-in)Then lock washer and locknut
Fig. 4. Adjusting nut sequenceSchematic, not to scale
Before moving on: the hub must spin smoothly by hand with no roughness, and there must be no rock when you push and pull the disc at 12 and 6 o'clock. If either fails, redo steps 3 to 8 with a new lock washer.

6. Fit the vented calipers and pads

The caliper torque and union torque are RAVE figures. The vented caliper itself is a Defender part, so the line routing is specific to this truck.

Bleed screw at the top, 15 Nm (11 lb-ft) Hose clear at full lock Union, 11 mm flare-nut, 15 Nm Two bolts, 13 mm 12-point 82 Nm (60 lb-ft), tightened evenly
Fig. 5. Caliper mounting and lineSchematic. Caliper position on the truck differs

Repeat sections 1 to 6 on the other side before bleeding.

7. Bleed the brakes

RAVE 70.25.02. The manual states this one method covers both ABS and non-ABS trucks.

Brake fluid rules from RAVE: use only DOT 4 from a sealed container. Never reuse fluid that has been bled out. Never let the reservoir fall below MIN during bleeding. Fluid strips paint, so wash any spill off with plenty of water.
A pressure bleeder may be used instead. RAVE limit: 4.5 bar (65 psi).
Do not drive on a soft, spongy or sinking pedal. Bleed again until the pedal is firm and high.

8. Finish and road test

Sources and limits

ContentSource
Hub removal, refit, preload, end playRAVE Discovery I workshop manual, Front Hub Assembly 60.25.01 and Front Hub overhaul 60.26.14
Disc bolts, run-out, minimum thicknessRAVE Front Brake Discs 70.10.10
Stub axle and mud shieldRAVE Front Stub Axle, ABS, 60.15.43
Caliper removal and refit, padsRAVE Front Brake Calipers 70.55.03, Front Brake Pads 70.40.02
BleedingRAVE Brake System Bleed 70.25.02 and General Brake Service Practice
All torque figuresRAVE torque tables, Front Axle and Brakes sections
Grease and fluid gradesRAVE Recommended Lubricants and Fluids
Socket sizesOwner write-ups for this axle. Not in RAVE. Confirm by fit
Swivel oil quantityWinston project spec sheet, 0.35 L per side

The vented calipers, vented discs and pads are Defender parts fitted as a conversion. RAVE for the Discovery I does not cover them, so steps marked "Not in RAVE" rest on general practice. The drawings were made for this guide and are schematic. Brakes, hub preload and wheel fixings are safety-critical: if a measurement is out of range, stop and fix it before driving.

0 steps done